www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com key features: ? 2w output power ? 5.7 kv isolation ? 15 kv/ s cmti ? 40 standard models ? miniature sip case ? -40c to +80c operation ? industry standard pin-out ? low cost mhi200di5.7 high isolation, 2w sip single & dual output dc/dc con vert ers input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.5 5.0 5.5 vdc 12 vdc input 10.8 12.0 13.2 15 vdc input 13.5 15.0 16.5 24 vdc input 21.6 24.0 26.4 input filter capacitor filter output parameter conditions min. typ. max. units output voltage accuracy ?.0 % output voltage balance dual output, balanced loads ?.1 ?.0 % line regulation for v in change of 1% ?.2 % load regulation, see note 2 see model selection guide ripple & noise (20 mhz) see note 3 100 mv p - p temperature coef cient ?.01 ?.02 %/? output short circuit momentary (0.5s max) general parameter conditions min. typ. max. units isolation voltage rated for 60 sec 5,200 vdc tested for 1 sec 5,700 isolation resistance 500 vdc 10 g? isolation capacitance 100 khz, 1v 7 pf common mode transient immunity 15 kv/? switching frequency 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +80 ? case +95 storage temperature range -55 +125 ? cooling free air convection humidity rh, non-condensing 95 % physical case size see mechanical diagram (page 3) case material non-conductive black plastic (ul94-v0) weight 0.08 oz (2.4g) reliability speci? cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 2.0 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (0.1 sec) 5 vdc input 9.0 vdc 12 vdc input 18.0 15 vdc input 20.0 24 vdc input 30.0 lead temperature 1.5 mm from case for 10 sec 260 ? caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. electrical speci? cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. series
www.micropowerdirect.com micropower direct 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com model selection guide model number input output ef? ciency (%, typ) load regulation (%, max) capacitive load (f, max) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) current (ma, min) nominal range full-load no-load mhi205s-03di5.7 5 4.5 - 5.5 446 35 3.3 500 10.0 74 ?0.0 1,650 1,000 mhi205s-05di5.7 5 4.5 - 5.5 500 35 5.0 400 8.0 80 ?5.0 940 1,000 mhi205s-09di5.7 5 4.5 - 5.5 493 35 9.0 222 4.4 81 ?0.0 940 1,000 mhi205s-12di5.7 5 4.5 - 5.5 492 35 12.0 168 3.4 82 ?0.0 440 1,000 mhi205s-15di5.7 5 4.5 - 5.5 501 35 15.0 132 2.6 79 ?0.0 440 1,000 mhi205d-05di5.7 5 4.5 - 5.5 513 35 ?.0 ?00 ?.0 78 ?5.0 440 1,000 mhi205d-09di5.7 5 4.5 - 5.5 504 35 ?.0 ?12 ?.2 80 ?0.0 440 1,000 mhi205d-12di5.7 5 4.5 - 5.5 504 35 ?2.0 ?4 ?.7 80 ?0.0 200 1,000 mhi205d-15di5.7 5 4.5 - 5.5 501 35 ?5.0 ?6 ?.3 79 ?0.0 200 1,000 mhi205d-1509di5.7 5 4.5 - 5.5 495 35 +15.0 66 1.3 80 ?0.0 200 1,000 -9.0 -110 -2.2 440 1,000 mhi212s-03di5.7 12 10.8 - 13.2 181 17 3.3 500 10.0 76 ?0.0 1,650 500 mhi212s-05di5.7 12 10.8 - 13.2 211 17 5.0 400 8.0 79 ?5.0 940 500 mhi212s-09di5.7 12 10.8 - 13.2 206 17 9.0 222 4.4 81 ?0.0 940 500 mhi212s-12di5.7 12 10.8 - 13.2 202 17 12.0 168 3.4 83 ?0.0 440 500 mhi212s-15di5.7 12 10.8 - 13.2 201 17 15.0 132 2.6 82 ?0.0 440 500 mhi212d-05di5.7 12 10.8 - 13.2 211 17 ?.0 ?00 ?.0 79 ?5.0 440 500 mhi212d-09di5.7 12 10.8 - 13.2 207 17 ?.0 ?12 ?.2 81 ?0.0 440 500 mhi212d-12di5.7 12 10.8 - 13.2 205 17 ?2.0 ?4 ?.7 82 ?0.0 200 500 mhi212d-15di5.7 12 10.8 - 13.2 199 17 ?5.0 ?6 ?.3 83 ?0.0 200 500 mhi212d-1509di5.7 12 10.8 - 13.2 204 17 +15.0 66 1.3 81 ?0.0 200 500 -9.0 -110 -2.2 440 500 mhi215s-03di5.7 15 13.5 - 16.5 143 16 3.3 500 10.0 77 ?0.0 1,650 300 mhi215s-05di5.7 15 13.5 - 16.5 169 16 5.0 400 8.0 79 ?5.0 940 300 mhi215s-09di5.7 15 13.5 - 16.5 160 16 9.0 222 4.4 83 ?0.0 940 300 mhi215s-12di5.7 15 13.5 - 16.5 162 16 12.0 168 3.4 83 ?0.0 440 300 mhi215s-15di5.7 15 13.5 - 16.5 155 16 15.0 132 2.6 85 ?0.0 440 300 mhi215d-05di5.7 15 13.5 - 16.5 165 16 ?.0 ?00 ?.0 81 ?5.0 440 300 mhi215d-09di5.7 15 13.5 - 16.5 160 16 ?.0 ?12 ?.2 84 ?0.0 440 300 mhi215d-12di5.7 15 13.5 - 16.5 164 16 ?2.0 ?4 ?.7 82 ?0.0 200 300 mhi215d-15di5.7 15 13.5 - 16.5 161 16 ?5.0 ?6 ?.3 82 ?0.0 200 300 mhi215d-1509di5.7 15 13.5 - 16.5 159 16 +15.0 66 1.3 83 ?0.0 200 300 -9.0 -110 -2.2 440 300 mhi224s-03di5.7 24 21.6 - 26.4 90 12 3.3 500 10.0 76 ?0.0 1,650 200 mhi224s-05di5.7 24 21.6 - 26.4 108 12 5.0 400 8.0 77 ?5.0 940 200 mhi224s-09di5.7 24 21.6 - 26.4 103 12 9.0 222 4.4 81 ?0.0 940 200 mhi224s-12di5.7 24 21.6 - 26.4 102 12 12.0 168 3.4 82 ?0.0 440 200 mhi224s-15di5.7 24 21.6 - 26.4 101 12 15.0 132 2.6 82 ?0.0 440 200 mhi224d-05di5.7 24 21.6 - 26.4 108 12 ?.0 ?00 ?.0 77 ?5.0 440 200 mhi224d-09di5.7 24 21.6 - 26.4 104 12 ?.0 ?12 ?.2 81 ?0.0 440 200 mhi224d-12di5.7 24 21.6 - 26.4 104 12 ?2.0 ?4 ?.7 81 ?0.0 200 200 mhi224d-15di5.7 24 21.6 - 26.4 103 12 ?5.0 ?6 ?.3 80 ?0.0 200 200 mhi224d-1509di5.7 24 21.6 - 26.4 102 12 +15.0 66 1.3 81 ?0.0 200 200 -9.0 -110 -2.2 440 200 notes: 1. the speci ed maximum capacitive load is for each output. 2. load regulation is measured over a range of 20% i out to 100% i out . 3. when measuring output ripple & noise, it is recommended that an external capacitor (1 f typ.) be placed from the +v out to the -v out pins for single output units and from each output to common for dual output models. 4. the converter should be connected to a low ac-impedance source. an input source with a highly inductive impedance may affect the stability of the converter. in applications where the converter output loading is high and input power is sup- plied over long lines, it may be necessary to use a capacitor on the input to insure start-up. in this case, it is recommended that a low esr (esr <1.0 at 100 khz) capacitor be mounted close to the converter. for 5v input units a 2.2 f is recom- mended; for 12v & 15v input units, a 1.0 f; and for 24v units a 0.47 f. 5. operation at no-load will not damage the unit, but they may not meet all speci ca- tions. 6. it is recommended that a fuse be used on the input of a power supply for protection. see the model selection tables for the correct rating. derating curve
www.micropowerdirect.com micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com notes: the mhi200x-xxd series is a good choice for igbt applications. they are designed to withstand the extra stress caused by the high voltage switching transients present in igbt drive circuits. the mhi2xxd-1509di5.7 models are speci - cally designed for use with ?62?type drivers. the igd962 (available from mpd ) is a hybrid integrated circuit speci cally designed to drive n-channel igbt modules. it provides the i/o isolation, high speed, drive voltage stability and fault protection required to control most mos gated power devices. the drawing at right illustrates a typical connec- tion of the mhi205d-1509di5.7 to the igd962 . for more information on this connection, please contact the factory. mechanical dimensions pin single output 1+v in 2-v in 5-v out 6 no pin 7+v out pin con nec tions notes: all dimensions are typical in inches (mm) tolerance x.xx = ?.02 (?.50) pin dual output 1+v in 2-v in 5-v out 6 common 7+v out igbt applications
|
